You are using an unsupported browser. Please update your browser to the latest version on or before July 31, 2020.
close

Showing articles from IC 2000 tag

IC Series Inverter/Charger: PREPARING THE DC CABLES

# PREPARING THE DC CABLES Go Power! supplies 2 ring lugs with the IC Series, which can be used for the Inverter/Charger end of the DC Cables. Source the correct ring terminals for the batteries you are using. * Cut the negative and positive cables to the required length. * Strip off enough insulation so you can …

IC Series Inverter/Charger: INVERTING MODE

In inverting mode: * The load power required by the appliances (fridge, TV, charger) is 2000W (16.7AAC x 120VAC) - 1. * The inverter supplies the 2000W or 3000W (186 ADC x 12VDC x 0.9) of AC power required to power the appliances - 2. * Shore power (utility or generator) is not connected. ![][1] [1]: https…

IC Series Inverter/Charger: UNIT ACCESSORIES

The IC Series Inverter/Charger has two accessories available: * IC Series remote (not included). * Battery temperature sensor (included). **IC Series Remote** This remote control device can be used for monitoring the performance of the unit. It is also used to program certain settings on the Inverter, Charger,…

IC Series Inverter/Charger: LOCATION AND ENVIRONMENTAL REQUIREMENTS

# LOCATION AND ENVIRONMENTAL REQUIREMENTS The IC Series Inverter/Charger must be installed in a location that meets the following requirements: **1. TEMPERATURE** Make sure the Inverter/Charger is installed in a location where the normal air temperature is between 0 °C and 50 °C. The cooler the better within this …

IC Series Inverter/Charger: DC WIRE SIZING

# DC WIRE SIZING SPECIFICATIONS The distance between the battery bank and the Inverter/Charger should be as short as possible to achieve maximum efficiency and to reduce fire hazards. The cables should be as short as possible and the overall length of both cables added together should be less than 10 ft (3m) to compl…

IC Series Inverter/Charger: BATTERY BANK CONFIGURATIONS

![][1] ![][2] [1]: https://hf-files-oregon.s3.amazonaws.com/hdpgopower_kb_attachments/2020/05-06/e9037356-bab6-4114-94b3-2b662d2bcf5d/battery%20wire.jpg [2]: https://hf-files-oregon.s3.amazonaws.com/hdpgopower_kb_attachments/2020/05-06/4a1d74d2-9931-4a5b-9d4f-424e1ff45f2b/battery%20wire%202.jpg

IC Series Inverter/Charger: AC WIRING

# AC WIRING INSTRUCTIONS The AC cables link the Inverter/Charger to the main panel and the sub panel. These cables handle the incoming alternating current (AC) utility or generator power, which can be passed through the Inverter/Charger to directly power the main appliances (pass-through mode) and/or used to charge t…

IC Series Inverter/Charger: GENERAL WIRING SPECIFICATIONS

# GENERAL WIRING SPECIFICATIONS The following sections detail how the IC Series Inverter/Charger should be wired. Before starting any wiring, read and understand these instructions. Wiring should meet all local codes and standards and be performed by qualified personnel such as a licensed electrician. The NEC (Natio…

IC Series Inverter/Charger: AC POWER SOURCE TYPES

# TYPES OF AC POWER SOURCE AC Input power to the IC Series can be supplied from a split-phase or dual- input single phase AC source. These sources typically include utility power or a generator. • **Split Phase**: This source has 4 lines: 2 Hot Lines, one neutral and one ground. The 2 hot lines are 120VAC and are 18…

IC Series Inverter/Charger: MOUNTING THE DRIP SHIELD

# MOUNTING THE DRIP SHIELD The IC Series Inverter/Charger is Marine UL listed. In order to properly mount the Inverter/Charger in a marine application, you must use a drip shield. Please follow the installation instructions below. **WALL MOUNT** ![][1] 1. Use the screws to mount the drip shield on the wall. ![][2…

scroll to top icon